5.0 Farad Digital Power Capacitor
QUESTIONS & ANSWERS
Ask a Question-
The led display on my capacitor stays lit and does not shut off. It stays on for days till the battery is dead.
If it is not going in to sleep ode you need to check your warranty option
-
My capacitor display will not shut off it is lit 24/7 what can I do ?
If the car is turned off the Capacitor should go to a sleep mode. If not check your warranty
-
How do you use the filament wire to charge the capacitor? Aren't you supposed to undo the ground wire to the battery? I'm going to use my regular 12 amp car battery directly to the capacitor.
Connect the ground wire to the Capacitors Negative Terminal
Place the one end of the resistor to the Positive trminal of the capacitor and the other end of the resistor powered by the Positive line from the car Battery.
Once the digital meter shows 7 to 9 volts. Take the risistor off and connect the positive wire direct to the Capacitor until it completes the charge
-
the led display on my pyle capacitor won't shut off. Can I reset it or what can I do?
LED will go to sleep mode in 10 to 15 seconds
-
Will this capacitor work on 6 volt ATV system. Actual voltage 7.2 to 7.6 volts.
Please contact us through our email support system to assist you further with your concern. Simply Go to pyleusa.com click on the CONNECT tab then on the drop-down choose Contact Us. Fill out the form and in the last part, you will have an option to write your Subject, and also on the comment box, you can write your concern about the product. Please allow at least 12 to 24 hours for someone to get back to you. You can also contact our support hotline at 718-535-1800 ext 2 during weekdays from 9 am to 6 pm EST.
-
Which side is positive and negative. Not clearly marked on my product. Thanks
the LED flash indicates the polarity of the terminals. The positive terminal has a red LED, and the negative terminal has a black LED. You can also look at the labels on the terminals, which are marked with a "+" and a "-" sign respectively.
-
The capacitor itself is wrapped in a protective plastic skin does that have to be removed before installation or does it stay on please let me know thanks
Please contact us through our email support system to assist you further with your concern. Simply Go to pyleusa.com click on the CONNECT tab then on the drop-down choose Contact Us. Fill out the form and in the last part, you will have an option to write your Subject, and also on the comment box, you can write your concern about the product. Please allow at least 12 to 24 hours for someone to get back to you. You can also contact our support hotline at 718-535-1800 ext 2 during weekdays from 9 am to 6 pm EST.
-
What is the maximum operating voltage for this unit? Is this compatible with 24 volt systems (peak voltages near 30v)?
The maximum operating voltage for the PCALPE50 is 12 volts DC. This unit is not compatible with 24 volt systems, as it will exceed the rated voltage and damage the unit
-
Can you use 1/0 wire on theee?
Please contact us through our email support system to assist you further with your concern. Simply Go to pyleusa.com click on the CONNECT tab then on the drop-down choose Contact Us. Fill out the form and in the last part, you will have an option to write your Subject, and also on the comment box, you can write your concern about the product. Please allow at least 12 to 24 hours for someone to get back to you. You can also contact our support hotline at 718-535-1800 ext 2 during weekdays from 9 am to 6 pm EST.
-
I recently installed the Pyle 5.0 Farad Digital Power Capacitor in my vehicle. Seems to be doing its job. My concern is that the LED lights are not turning off. Any suggestions or ideas on correcting that issue?
The capacitor is wired incorrectly or has a faulty ground connection. You should check the wiring diagram and make sure the capacitor is connected to the positive terminal of the battery and the amplifier, and the negative terminal is grounded to the chassis of the car.
-
This capacitor is draining my battery when the car is off. I can here it beeping from outside the car as the voltage drops from killing my battery. How do I fix this?
You can Try connecting through the ACC so that whenever the Key is off poawer is also off on the Cap