Bluetooth Receiver Connectivity:
What’s in the Box:
Receiver Technical Specs:
Extend Warranty Protection and Earn Rewards. Click HERE for Registration
QUESTIONS & ANSWERSAsk a Question
I need the small remote for the PLRMR 23 BTW.
Please do not hesitate in contacting us through our email support system. Simply Go to pyleusa.com click on the CONNECT tab then on the drop-down choose Contact Us. Fill out the form and in the last part, you will have an option to write your Subject, and also on the comment box, you can write your concern about the product. Please allow at least 12 to 24 hours for someone to get back to you. You can also contact our support hotline at 718-535-1800 ext 2 during weekdays from 9 am to 6 pm EST.
For Parts Request Please Complete the information below:
Model Number: PLRMR23BTW
Requesting Part: PRTPLMRB29WRC
Trying to replace my screen on my car radio pld 10 b 2 is the production number
Please send the unit in for repair
Please contact us through our email support system to assist you further. Simply Go to pyleusa.com click on the CONNECT tab then on the drop-down choose Contact Us. Fill out the form and in the last part, you will have an option to write your Subject, and also on the comment box, you can write your concern about the product. Please allow at least 12 to 24 hours for someone to get back to you. You can also contact our support hotline at 718-535-1800 ext 2 during weekdays from 9 am to 6 pm EST.
What is the current draw when the unit is powered down? Is there a difference in the current draw (when the power switch on the unit is turned off) if the yellow and red wire both connected to +12 volts constant power verses the yellow being hooked to +12 volts constant power and the red hooked through the accessory switch on the ignition?
Yes, there is a difference, When the unit is off the active line is the yellow wire which draws minimal current to supports the system to keep the clock running and to hold the stored memory and system functions. Once turned ON the internal Amplifier will begin to work and that is the one that draws a high current to support audio.
What is the warranty
30 days Warranty for replacement from the seller and 1Year Repair and service warranty from the manufacturer.
is this unit water proof
I would say it is water-resistant but not totally water proof as there are ports that water may penetrate if it get soaking wet
I need an antenna for this unit. PLRMR23BTW Marine Stereo Receiver. Where can I find one?
Please check the link
Hello I have installed 2 different Pyle-PLRMR23BTW radios on my boat, I replaced another radio and put this radio in the boat the first time I changed it after hooking up power and ground wires only nothing came on so I returned the radio and picked up the same exact radio and re installed it but this time I double checked that maybe I might have made a mistake but since my background is in electricity and previous was in car audio I checked the voltage which is giving 13.66 volts on constant and 13.67 on switched. Is there anything else I should be doing to get this model to power up?
Have you got the Yellow wire to a constant +12 volts, Red on ACC +12 volts switched and Black to ground? These three-wires needs to be properly wired to get the radio to turn on
Unit installed OK but there is no sound from the speakers. I am not a novice at this... All wiring triple checked. Wired harness to two front channel Bose waterproof 4 ohm speakers. All the channels and modes seem to respond and the display appears to be getting a signal from local FM stations. I Secured the two Rear channel wires so they are not touching anything. It appears that the output amp section inside this unit is dead on arrival. This is a PLMRMR23BTW - PO44521190600867. Can you replace this defective unit.
Double-check the RED and YELLOW Wire make sure that they are both getting a +12volts
SPA Installation: If I have only a RED, could I wired the Yellow and the Red together ? I Tried only with the Red and no powering up... Thanks !
Yes you can combine the yellow and red
I only have two speakers on my boat, is it a problem to leave the unused speaker outputs unterminated? Or if they need to be terminated, how to do so without adding additional speakers? If not a problem, is it best to used front or rear connections or is it irrelevant?
Just make sure the unused wires are secured and not touching any other wires
unit is not powering up. We are getting power through negative side and positive side when we wire it up.
To power up the PLRMR23BTW you need to have the Yellow wire to be connected to the 12 volts with constant power and the RED wire to the 12 volts Ignition switch and the BLACK wire is the ground wire or the negative.