Home Wall Mount Speaker System PDWR53BTWT
What’s in the Box:
Extend Warranty Protection and Earn Rewards. Click HERE for Registration
QUESTIONS & ANSWERSAsk a Question
I can not find any information on how to use the Balance inputs using the 5 pin connector. Labeled L+L-GNDR+R-. I assume some sort of variable resistor or pot but what value and how connected? I figured out the loop is a TRS line level and saw, somewhere, that the sub is a TS mono for a powered sub. The USER MANUAL lists nothing re connection type or levels. Very sad...
You can use a 3 core wire for the Left and right channels and a 1/4" plug or XLR to the source preamp
Are these stand alone blue tooth speakers that can connect to one device or are do they need to be wired together. If Wiring is required can more than two be connected so that they all are connected to the same Bluetooth Signal
You can connect another set of speakers using the loop out and AUX input of the speaker
When I try to connect to Bluetooth it’s asking for pin number. I don’t have PIN number
You can use 0000
How do I daisy chain the speakers? Am I supposed to connect from the RCA plugs to the binding posts, or the single auxiliary to the binding posts? The link to the manual does not work and I want to be sure I purchase the correct cable.
It is the Green Phoenix connector to binding post
How do we connect to a device (IOS) when the network PyleUSA does not display as a bluetooth device? Is there a way to reset the bluetooth signal?
Double-check if there are other devices previously connected to the speaker. This may prevent you from connecting the speaker
What is the difference between ON and Auto?
ON is continuous power. Auto. During power ON mode, light is constant blue color; During power AUTO mode, lights go off when there is no signal input and it turns to a blue color when the signal comes.
Are you able to connect 4 of these together?
If you wish to connect wirelessly. It is not possible. But it can be connected by wired through loop and aux in
My puppy got ahold of my speakers (AC120-240v) electrical cord; yes they chewed it up! Sigh…. Can you recommend a generic cord, or do you all have replacement cords? Thanks in advance.
Please check the link.
How do I make the ACTIVE speaker the RIGHT speaker?
There is ni option to switch the speakers left to right
was there supposed to be speaker wire w/these? The manual indicates that there was.
Speaker wire is not included. 16AWG is recommended
How much does each of the PDWR53BTBK speaker weigh?
We only have the total weight
Weight: 12.12 lbs.
Do you have any longer Power cords for the PDWR53BTBK speakers that you can purchase? The 3.9 foot length is not very long if your outlet is down near the bottom of the wall. Can you use an extension cord? That is not the ideal work around either.
You can use an extension cord
Is it possible to order just the wall mount brackets for these speakers?
Brackets only comes with the package
I am looking at these speakers and am a bit confused by what I’m reading. I want speakers that connect via blue tooth to my stereo receiver, eliminating the need for speaker wires. My receiver is already connected to all the other components, so that’s the only connection needed. Also, it appears the speakers must be attached to each other. Is this the case? And what is active vs passive ? Thank you for your response, and I would appreciate any additional information you would like to provide. Marsha Elrod
The active speaker is the one with the amplifier as well as the controls. A passive speaker is the one with a speaker terminal only. This model is a stand-alone speaker. it does not need an external amplifier to run these.
Good Morning I recently purchased the PDWR53BTWT speakers. I connected my tv to input but I can't control the volume like I do with my phone. what amI doing wrong? regards Mario Lima
Check If the connection on the back of the TV is connected to the Audio output and to the PDWR53BTWT Aux in
Can these be mounted on my patio? They might get a little wet if we have a heavy rain, but they would be under a pretty large overhang.
The PDWR53BTWT is not water-resistant since there are jacks where moisture can go in the unit.
Is there an installation video on these ?
There is no video that we can share to you on how to install the speaker but we guarantee you that we can assist you to get this together quickly over the phone or through email.
Please do not hesitate in contacting us through our chat support system at www.m.me/PyleUSA should there be any other concerns or changes with your order. You can also contact our support hotline at 718-535-1800 ext 2 during weekdays from 9 am to 6 pm EST.
I lost the 2 pin Phoenix connecter. What size is the connector so I can order new one?
Please contact us through our email support system to assist you further with your concern. Simply Go to pyleusa.com click on the CONNECT tab then on the drop-down choose Contact Us. Fill out the form and in the last part, you will have an option to write your Subject, and also on the comment box, you can write your concern about the product. Please allow at least 12 to 24 hours for someone to get back to you. You can also contact our support hotline at 718-535-1800 ext 2 during weekdays from 9 am to 6 pm EST.
What is the right + and - ground and left + and - for
If you are refering to the 5PIN Phoenix Connector. It is for a hard wireing of LINE IN
I purchased the Home Wall Mount Speaker System PDWR53BTWT. It arrived without having the stereo connecting cable, what type of cable connector do i need to order to connect the speakers?
Amazon.com: RCA to Bare Wire Speaker Cable 14AWG OFC The Conductor of The red Wire is Connected to The Positive Pole, Suitable for Direct Connect Speakers or DIY Speaker Plugs (10.00) : Electronics
I will be installing these in a classroom. Can the bluetooth be turned off? Also, The link to the manual is broken.
The Bluetooth is always on