1 6

4-Channel Car Amplifier 2000W Power MOSFET Silver RCA Inputs

4-Channel Car Amplifier 2000W Power MOSFET Silver RCA Inputs

$108.99
$108.99 $155.70
Sale (30%) Sold out Save $46.71
  • 3 Year Warranty
  • 30-Day Returns
  • Free Shipping in U.S.

View full details

About this item

Product Highlights
When power isn't enough, you need Pyle Power. This four-channel, 2000-watt power supply is bridgeable. It's equipped with everything you've come to expect from quality car amplifiers. The RCA ports are silver-plated for eliminating signal loss. A subsonic filter allows low-end interference to be cut, so your speakers will always be delivered the highest quality audio. The MOSFET pulse width modulation power supply allows for a clean, distortion-free signal to your speakers. To keep both your car and the amplifier safe, this model is equipped with thermal, overload, and short circuit protection. So when what you need is power, trust Pyle Power.
DETAILS
  • Maximum Power Output 4 x 500W
  • Bridgeable RMS Power @ 4 Ohms: 2 x 1000W
  • 4 Channel Bridgeable MOSFET Amplifier
  • Frequency Response 20 Hz-50kHz (±3dB)
  • Output Power @ 14.4v DC, 50Hz
  • 2 Ohm Stable
  • MOSFET Power Supply
  • PWM ( Pulse-Width-Modulation ) System
  • Glass Epoxy PCB
  • Silver RCA Inputs
  • Custom Terminal Block for Speaker Connection
  • Thermal / Overload / Short Circuit Protection
  • Input Impedance: 47K Ohms
  • Soft Turn On/ Off
  • Advanced Protection Circuitry
  • S/N Ratio: >90dB
  • Dimensions:10.24''W x 2.21''H x 14.58''L
    • Specification
    When power isn’t enough, you need Pyle Power. This four-channel, 2000-watt power supply is bridgeable. It’s equipped with everything you’ve come to expect from quality car amplifiers. The RCA ports are silver-plated for eliminating signal loss. A subsonic filter allows low-end interference to be cut, so your speakers will always be delivered the highest quality audio. The MOSFET pulse width modulation power supply allows for a clean, distortion-free signal to your speakers. To keep both your car and the amplifier safe, this model is equipped with thermal, overload, and short circuit protection. So when what you need is power, trust Pyle Power.
    MANUALS & DOWNLOADS

    PLA4278 - Manuals

    Questions & Answers

    QUESTIONS & ANSWERS

    Ask a Question

    • I have a very similar amp to this it's a Pyle PLA2678 is this 2 ohm stable as I currently have 4 12" Pyle blue wave subwoofers and was going to connect the subwoofers to run at ² ohm as they are dvc. Would this be ok.

      That will be fine

    • I bought a app from yard and I think it went out

      If your Pyle PLA4278 car amplifier completely stopped working or won't turn on, you can perform a few simple checks to see if it is actually broken or if it is just a wiring issue:

      1. Check the LED Indicator Lights: Look at the side panel of the amplifier while your car is running and the radio is on.

        • If the Power (Green) LED is off, the amp isn't getting electricity.

        • If the Protection (Red) LED is on, the amplifier went into safety mode to prevent damage. This usually means a speaker wire is shorting out, the ground wire is loose, or it overheated.

      2. Check the Built-In Fuses: There are physical automotive fuses plugged directly into the side panel of the amplifier. Pull them out and look at the metal strip inside. If the strip is broken or burned, replace them with new fuses of the exact same amperage rating.

      3. Verify the Main Power Fuse: Check the large inline fuse on your main power cable right near your car battery. If this fuse is blown, no power will reach the trunk.

      4. Test the "Remote" Wire: The amplifier needs 12V power on the REM terminal to know when to turn on. Use a multimeter or a 12V test light to ensure that terminal is getting power when the car radio is switched on.

      5. Inspect the Ground Connection: Make sure the ground wire is tightly screwed into bare, unpainted metal on the car's chassis. A loose or rusted ground wire will cause the amp to intermittently cut out or stop working entirely.

    • Can I run two fifteen on your two thousand and one amp and it will be okay

      Yes, you can run two 15-inch subwoofers on the Pyle PLA4278, but you have to wire them very carefully to keep the amplifier from overheating or frying.

    • I have 2 10” subs that r 400rms and 2ohm with this amp work

      The Pyle PLA4278 4-channel amplifier will work with your two 10-inch subwoofers, but you must wire them carefully to avoid overheating the amplifier.

    Every order includes:

    files/Group_1_1.svg
    Free Shipping
    Anywhere in the USA
    files/Group_3.svg
    3-Year Warranty
    Coverage on all products
    files/Group_2.svg
    30-Day Returns
    Easy and hassle-free
    files/Group_4.svg
    Trusted Brand
    Backed by loyal customers